|
|
 |
|
Steel Decking
The AIR/SAFE® Fastening System
PNEUTEK®
The established leader in mechanical attachment of steel roof & floor deck.
Pneutek's® Decking Fasteners are made of one piece "uni-construction"
for highest shear strength and ease of inspection.
Click any of the titles below to see short-subject videos:
Forced Entry System | Applications | Loading | Installing | Installing a Large Job: 1 • 2
Dealing with Obstructions | Punching on a Wet Surface | Reloading
|
The ERGONOMIC Stand-Up Air/Safe® Steel Decking Tool |
|
|
| Steel decking to structural supports | |
|
| The ERGONOMIC Stand-Up Air/Safe™ Steel Decking Tool | |
The AIR/SAFE® Fastening System by Pneutek® ... the fastest, safest, most economical system for attaching steel roof and floor deck.
|
|
| Pneutek's Steel Decking Tool |
|
Unlimited Steel Thickness...Only Pneutek's®
pneumatic tools can fasten into all commercially specified steel substrate grades of 1/8" thickness and up, including A992 type steel up to 100 ksi tensile strength.
Lowest In-Place Fastener Cost... Pneutek's®
fully automatic magazines hold thirty to fifty fasteners, eliminating frequent reloading of powder charges and fasteners. The fastest deck attachment system available today!
Air/Safe Pneumatic Design... Pneutek's®
patented low-velocity actuation design meets or exceeds ANSI and O.S.H.A. safety requirements.
Corrosion Resistant... Pneutek® fasteners are produced in yellow mechanical zinc plating for enhanced corrosion resistance, and have been evaluated in accordance with salt spray test specification ASTM-B117. |
|
| Auxiliary Tank Assembly and Hose |
|
MODEL NO. ATA-17; 17 gallon ASME tank
assembly equipped with pressure regulator,
safety valve, male connector and female coupler.
MODEL NO. AHA-50; 1/2" 50 ft., 300 psi air hose
assembly with a 3/8" female coupler and 3/8"
male connector.
MODEL AHA-100; 1/2" 100 ft., 300 psi air hose
assembly with a 3/8" female coupler and 3/8"
male connector.
| Pneutek® Portable Air Compressors |
|
MODEL NO. PC-2S13KES-20: Two-stage, 12.5 hp. Kohler engine. Delivers 20 cfm @ 175 psig.
MODEL NO. PC-2S22KES-40 : Two-stage, 22 hp. Kohler engine. Delivers 39.5 cfm @ 175 psig. |
| Air/Safe Trigger Lock/Steel Decking Tools |
 |
MODEL NO'S:
PT-800 • PT-1200
PT-1400 • PT-1500
FASTENERS ARE SUPPLIED
PRE-COLLATED FOR RAPID LOADING |
 |
| |
| |
| Steel Substrate Thickness |
Recommended Pneutek Fastener Part No.'s |
Recommended Pneutek
Tool Model No.'s2,3 |
| Inch |
MM |
1/2"(12.7MM) Dia. Head |
3/8"(10MM) Dia. Head |
| .113 to .155 |
2.8 to 4 |
SDK61075 |
K41075, SDK42075 |
PT-400S, PT-400Z |
| .155 to .250 |
4 to 6 |
SDK63075 |
SDK43075 |
PT-400S, PT-400Z,
PT-1500S PT-1500Z |
| .188 to .312 |
5 to 8 |
K64062, K640751 |
K43050, K44062, SDK440751 |
PT-1500S, PT-1500Z,
PT-2000Z |
| .281 and up |
7 & Up |
K66062, K660751 |
K45056, K45062,
K450751 | |
| NOTES: |
1. Must be used for the attachment of four thicknesses (overlap condition) of 20 ga. steel deck, or three or four thicknesses of 18 ga. or 16 ga. steel deck, to the indicated substrate.
2. Tools with suffix "S" are for 3/8" (10mm) head dia. fasteners 3. Tools with suffix "Z" are for 1/2" (12.7 mm) head dia. fasteners |
APPROVALS/RECOGNITIONS
• Steel Deck Institute Diaphragm Design Manual, first, second & third editions
• West Virginia University Reports No. LP996, LP1199 & 8-24-98
• Factory Mutual Research Corporation (Class 1 Fire Rating & Class 1-60 and 1-90 Wind Uplift Ratings) Reports No. 28234, J.I. 1R8a6.AM & Form 797
• I.C.B.O./I.C.C. Evaluation Service Research Reports No. ER-3829, ER-2078P (verco Mfg. Co.) & ESR-1414 (ASC Profiles)
• City of Los Angeles, CA, Research Report No. RR25382
• U.S. Army Corps of Engineers Guide Specification No. CEGS-05311
• City and County of San Francisco, CA, Code Ruling BC-105-3
CAUTION/WARNING -To avoid serious injury, all tool operators and personnel within 75 ft. should wear hearing and eye protection in any environment, i.e. earplugs/earmuffs safety glasses. All Pneutek fasteners must be installed by personnel trained by Pneutek, Inc. or by its authorized distributors. All Pneutek products must be used in accordance with Pneutek's operating instructions. Do not fasten into stainless steel or other brittle surfaces. Do not use bottled CO2. Oxygen or Air as a source of power to operate Pneutek fastening tools - use only air from Pneutek approved compressors. The Pneutek Air/Safe Fastening System is covered by one or more of the following U.S. patents: 4,196,833; 4,040,554; 3,952,398; 3,954,176; 3,927,459; 4,128,110; 4,098,171; 4,122,904; 4,051,862; 4,098,295; 4,106,618; 4,106,619; 5,366,082; 5,645,208. Other patents pending. Copyright 2006 Pneutek, Inc. Hudson, NH, U.S.A. All Rights Reserved. | |
| |
